

Exterior painting
Exterior House Painting in Inola and the Tulsa Area
Daniel's Custom Painting paints house exteriors in Inola and across the Tulsa area. A good exterior job starts with the surface: wash, scrape, repair, caulk, prime, then paint. Oklahoma sun, wind, hail and freeze-and-thaw swings are hard on paint that goes over loose or damp surfaces, so prep decides how long the finish lasts.
- Serving Inola, Claremore, Tulsa, Broken Arrow and nearby
- Exterior, interior, cabinet and commercial painting
- Call or request an estimate online
Get an exterior estimate
Tell us about your house and which sides, trim and doors you want painted. We will explain what it needs and how we would approach it.
What exterior painting includes
Exterior painting means preparing the outside of the house and then applying primer and finish coats to siding, trim, doors and other painted surfaces. This table shows how it works here.
| Topic | How it works |
|---|---|
| Surfaces | Tell us what your house is clad in, such as wood, brick, vinyl or stucco. We will say what is practical to paint. |
| Prep | Wash, scrape, sand, repair, caulk and prime, in that order. See the steps below. |
| Coats | Primer on bare or repaired spots, then finish coats. Two finish coats is a common standard. |
| Time on site | Depends on size, stories, repairs and weather. See "How long an exterior paint job takes". |
| Estimate | Call or send the form. We call you back at the number you gave. |
| Where | Inola, Claremore, Tulsa, Broken Arrow, Owasso, Jenks, Bixby and nearby. See service areas. |
Surfaces on a house exterior
Condition matters more than material: sound surfaces take paint well and soft or damp ones need repair first. Tell us what your house is clad in and we will say what is practical to paint. Here is what to know about each common surface.
- Wood and lap siding. Wood expands and contracts with heat and moisture, so loose paint and open joints are the usual problems. Scraping, sanding, caulk and primer on bare wood come before the finish coats.
- Brick and stone. Brick is porous. Paint, stain and limewash behave differently, and painted brick is hard to reverse, so decide before you start. Moisture has to be able to escape. See what to ask about painting brick.
- Vinyl and aluminum. These can be painted with products made for them. Dark colors on vinyl can cause heat distortion, so manufacturers often limit how dark you can go.
- Fiber cement. It holds paint well when it is clean, dry and primed. Cut edges and joints need sealing.
- Stucco. Hairline cracks and chalky surfaces need cleaning and patching, and coatings are chosen for flexibility and breathing.
- Trim, fascia, soffits and gutters. These take the most weather. Soft or rotted wood is repaired or replaced before paint.
- Front and garage doors, shutters. Doors and shutters can often be painted in place with careful masking. See painting shutters and doors without removing them.


Siding

Stucco
Weather sets the schedule. Paint needs dry surfaces and the right temperature, so a rainy week moves the work.

Peeling paint, ladder in place

Chipped white wash being scraped

Ladders and masking at a gable
Questions about your house?Call (918) 704-5861Describe your house
Paint systems for Oklahoma exteriors
The right system depends on the surface. This table lists product classes, not brands, because prep and system matter more than the label.
| Surface | Usual system | Why |
|---|---|---|
| Wood siding and trim | Bonding or stain-blocking primer on bare wood, then 100% acrylic latex | Flexes with wood movement and resists blistering |
| Brick and masonry | Masonry primer and a breathable masonry or acrylic coating | Lets moisture escape; porous brick soaks up thin coats |
| Fiber cement | Primer made for cement board, then acrylic latex | Seals a porous surface and holds color |
| Vinyl and aluminum | Paint made for the material in light-reflective colors | Avoids heat buildup and warping |
| Stucco | Masonry or elastomeric coating after crack repair | Bridges hairline cracks and sheds water |
| Metal doors | Rust-inhibiting primer and enamel | Stops rust bleed and wears well on hardware |
| Concrete patios and steps | Coating made for concrete over a cleaned, sound surface | Holds up to foot traffic |
Whatever the product, we follow the manufacturer's data sheet for temperature, dew point and recoat time.
Built for Oklahoma weather
Oklahoma weather gives exterior paint a short working window and a hard life. The National Weather Service numbers for Tulsa (1991-2020 normals) show why.
The NWS notes that the Tulsa area is "occasionally subjected to large hail and violent windstorms", mostly in spring and early summer. What that does to paint, in plain terms (our reading of those numbers, not a measurement): hot surfaces and direct sun can dry coats too fast, long freezes and thaws crack film on wood, humidity feeds mildew on shaded sides and hard storms drive water behind loose paint.
When the usable windows are. Spring (late March to May) and fall (September to early November) usually give the mildest dry stretches, but May and June are wet, so build in rain days. Some manufacturers' exterior latex products list a minimum of about 35 F and a surface that stays above the dew point for about 48 hours after application, while traditional latex needs warmer weather. Many data sheets also advise against painting in direct sun on hot days. Always read the product data sheet. For the month-by-month view, see when to paint a house exterior in Oklahoma.
How long an exterior paint job takes
The time depends on house size, number of stories, how much scraping and repair the surfaces need, the number of coats, drying time between coats and weather days.
A small one-story house with sound paint can go faster than a tall house with heavy peeling and trim repair. Ask any painter for a start-to-finish estimate in days and what happens on a rain day.
Older homes and lead-safe work
Homes built before 1978 may contain lead-based paint. Federal rules require firms paid to disturb painted surfaces in most pre-1978 homes to be certified by EPA (or an authorized state) and to follow lead-safe work practices. In Oklahoma the program runs through the Department of Environmental Quality. Ask any contractor for proof of certification before scraping or sanding starts.
Source: U.S. EPA, Lead Renovation, Repair and Painting Program (epa.gov/lead/renovation-repair-and-painting-program); Oklahoma DEQ lead-based paint program.
Many local homes fall in the pre-1978 range. These are city medians, not facts about your house.
For the full rule and what to ask, read lead-safe painting for pre-1978 homes.
Permits, HOA rules and historic districts
Repainting is usually cosmetic work, but the rules depend on your city, your neighborhood and the work involved.
- Tulsa. The City of Tulsa's Development Services page lists project types that do not require a permit, including "Painting walls, adding floor tiling or carpeting". It says walls, so ask the city about exterior work or any repairs to the house. Development Services: (918) 596-9456.
- Tulsa historic districts. The Tulsa Preservation Commission says it "does not regulate paint color". A certificate is needed only to paint a masonry building that was not previously painted, so never paint unpainted brick or stone without asking first.
- Inola and Rogers County. Neither Inola City Hall ((918) 543-2430) nor Rogers County Building Safety and Inspection Services ((918) 923-4874) publishes a rule about repainting. Confirm with them before work that replaces siding, framing, wiring or plumbing.
- Other cities. Many cities do not require a permit for repainting, but rules differ and work that changes siding, framing, wiring or plumbing may need one. Check with your city's building department before work starts. Ask any contractor in writing who handles permits and city registration, if any apply.
- HOAs. A homeowners association has its own color and material rules. Check them before you choose a color.
Source: City of Tulsa Development Services (cityoftulsa.org, plans review); Tulsa Preservation Commission FAQ (tulsapreservationcommission.org/summer-project-faq); Inola City Hall (inolaok.com); Rogers County Building Safety and Inspection Services.
What changes the price of exterior painting
The price depends on the size of the house, the condition of the surfaces and how much prep and repair they need. These are the main drivers.
| Driver | Why it matters |
|---|---|
| House size and stories | More surface and taller walls mean more time, ladders or lifts |
| Siding material | Brick, stucco and rough wood take more prep and coating than smooth newer siding |
| Condition of the paint | Peeling, chalking and mildew need scraping, washing and priming first |
| Wood repair | Soft or rotted trim, fascia and boards are repaired or replaced before paint |
| Trim and detail | Shutters, small window panes, soffits and decks take more hand work than flat siding |
| Color change | Dark to light, or bare surfaces, usually need primer and extra coats |
| Access | Steep grades, tight gaps and tall walls add setup |
| Prep scope | Washing, caulking and priming are separate line items on many quotes |
Compare quotes by scope, not by the bottom line. A good quote names each area, the prep for each, the number of coats and what happens if rot turns up. See how to compare painting quotes.
Send us a few photos or describe each side of the house. We will explain what the job involves and what moves the price.
Want a ballpark?Call (918) 704-5861Get a Ballpark
Ask any painter who protects landscaping, vehicles, windows and pets, and who your contact is on site.
Exterior painting photos
Photos from the exterior painting gallery. They show the surfaces and details described above. See the full set in the painting portfolio.
Where we paint
Daniel's Custom Painting works in Inola, Claremore, Tulsa, Broken Arrow, Owasso, Jenks, Bixby and nearby Oklahoma communities.
- Inola
- Catoosa
- Claremore
- Verdigris
- Tulsa
- Broken Arrow
- Owasso
- Jenks
- Bixby
Our base for service-area questions is Inola and Rogers County, and drive times and local permit notes for each city are on the service areas page. Painting a house in Tulsa, Broken Arrow, Owasso, Claremore, Jenks or Bixby? Call (918) 704-5861 and tell us your ZIP.
Painting the inside too? See interior painting. More on residential painting and about Daniel's Custom Painting, or browse all painting services.
Exterior painting questions
Cost and value
How much does exterior painting cost?
The price depends on the size of the house, how many stories it has, the siding material, the condition of the old paint, how much scraping, caulking and wood repair is needed, the number of coats and how many details such as trim, doors, shutters, soffits and garage doors are included. Brick, stucco and heavily weathered wood take more prep than newer siding, and tall or complicated houses need ladders, lifts or scaffolding. Rot repair and washing are separate line items on many quotes, and a dark-to-light color change adds coats. National cost guides publish wide ranges that vary by region, so treat any online number as a starting guess only. Get a written scope that lists each area and the prep steps, then compare quotes on that basis rather than on the bottom line alone. Ask whether washing, caulking and priming are included, who removes shutters or fixtures, how many coats go on, and what the written price assumes about repairs. A quote that names each area makes it much easier to see why two prices differ.
Do painters charge by the square foot, by the hour or by the job?
Practices vary. Some painters quote by the job after a walk-through, some by square foot and some by the hour or day. Square footage can mean living area, actual wall surface or paintable area after windows and doors, so two quotes that look different may be measuring different things. A fixed price tied to a written scope is easiest to compare, while hourly pricing leaves the final cost open. Whatever the method, ask what area was measured, what prep, paint and trim it covers and how changes are handled, because a low rate on a big number can cost the same as a high rate on a small one.
Is exterior painting a capital improvement?
For your own home, repainting is generally maintenance rather than an improvement. IRS Publication 523 lists painting, interior or exterior, among repairs whose cost is not added to your home's basis, unless the painting is done as part of an extensive remodeling or restoration, which can make the whole job an improvement. Rental and business property follow different rules, so check with a tax professional.
Next step: residential painting
Timing
When is the right time of year to paint a house exterior in Oklahoma?
Spring (late March to May) and fall (September to early November) usually give the mildest dry stretches. Tulsa averages about 74 days a year at or above 90 degrees and about 72 days at or below freezing (National Weather Service, 1991-2020 normals), so the usable season sits between those extremes. May and June are the wettest months, so spring jobs need rain-day buffers. Paint must also stay above the dew point and inside the temperature range printed on the can. Book early for spring and fall.
How long does an exterior painting job take?
A typical house takes several days to a couple of weeks depending on size, stories, prep, repairs and the number of coats, and rain days stretch the schedule. Washing and prep come first, then priming bare spots and two coats on walls and trim, with drying time between each coat. Complicated homes with lots of trim, tall walls, heavy scraping or wood repair take longer, while a single-story house in good shape is quicker. Weather matters most: latex paint needs hours of dry time before dew or rain, and cool or humid days slow curing. Ask for a start date, a finish estimate, how weather delays are handled and when the final touch-up and walk-through happen. A written schedule that names the prep days separately from the painting days is a good sign. Also ask how many people will be on site each day, because crew size changes the schedule as much as house size does.
Can you paint a house exterior in cold weather?
Sometimes. Some premium exterior latex paints are made for application as low as 35 degrees, while traditional latex needs it warmer, and the surface must stay above the dew point for about 48 hours after painting, according to one major manufacturer's exterior FAQ. Frost, dew and cold nights can ruin the cure. Check the can's temperature range, watch the overnight low and expect shorter work days. In Tulsa the average last freeze is in late March and the first in early November.
What weather stops exterior painting, and how soon can it rain after?
Rain, heavy dew, high wind, frost and surfaces that are too hot or too cold. One major manufacturer says latex paint needs at least four hours of dry time before moisture settles on it, and advises waiting at least a day after heavy rain so wood and masonry can dry. Painters check the forecast, wait for siding to dry in the morning and stop early when dew is coming. A few weather delays are normal in any exterior schedule.
Can I paint the outside of my house in the summer heat?
It can be done, but with limits. Tulsa averages 24 days at or above 90 degrees in July (National Weather Service), and a manufacturer's exterior FAQ warns that temperatures over 100 degrees can make paint dry before it bonds, and says to avoid painting in direct sunlight in hot months. Painters work early, follow the shade around the house and stop when surfaces get too hot. A hot-weather job needs a flexible schedule.
Process and scope
What prep happens before a house exterior is painted?
Washing off dirt, chalk and mildew, scraping and sanding loose paint, caulking gaps, repairing damaged wood, spot-priming bare or patched areas and masking what should not be painted. Purdue Extension notes that poor cleaning of old paint is a frequent cause of peeling. Prep takes more time than painting and is what makes a job last. Ask every painter to list the prep steps in the estimate.
What kind of exterior paint holds up in Oklahoma weather?
Look for a 100 percent acrylic latex product made for exteriors, with good UV and mildew resistance and a finish suited to the surface. Oklahoma swings from hot, humid summers to freezing nights, so flexible paint that can expand and contract helps it resist cracking. Compare the product data sheets for temperature range, coverage and coats rather than relying on marketing claims. Ask the painter which line they plan to use and why.
How long does exterior paint last in Oklahoma?
It varies with the product, the prep and which way the wall faces, so there is no single number. As a rough rule many painters see a good exterior repaint holding up for several years on wood and longer on well-prepared vinyl, fiber cement or metal, with south and west walls wearing first. Sun, heat swings, humidity, hail and wind all age paint, so watch for chalking, peeling, cracked caulk and bare wood. Fix small failures early.
Should the house be pressure washed before painting?
The surface must be clean and dry for paint to bond, so washing is part of prep when dirt, chalk, mildew or flaking paint are present. Pressure and technique should match the siding, with a gentler wash for wood and a long drying time before paint goes on. Too much pressure can force water behind siding. A painter should tell you how the house will be cleaned and how long it will dry.
Should I paint my brick house?
Painted brick is hard to reverse, because the paint soaks into the pores. Painting it adds ongoing upkeep, and a bad coating can trap moisture and flake. Brick that is crumbling, efflorescing or damp needs repair first. If you want a lighter look, ask about alternatives such as limewash or a breathable masonry coating. Tulsa's historic-district rules can require a permit to paint masonry that has never been painted, so check before you start.
Why is the exterior paint on my house peeling?
The most common cause is moisture. Purdue Extension says moisture is the most common reason for early paint failure on wood, from rain and dew soaking in or from indoor vapor moving outward. Poorly cleaned old paint, thick coats and painting in the heat or on damp surfaces also cause peeling and blisters. Find and stop the water source first, then scrape back to sound paint, prime and repaint.
How do I choose exterior paint colors?
Start with the things that will not change, such as brick, stone, roof and driveway, then choose colors that complement their undertones. Test large samples on more than one side of the house and look at them in morning and evening light. Dark colors fade faster in strong sun and show dirt and flaws, and an HOA may limit your options. Ask for a photo-based mockup if you are unsure.
Next step: residential painting
What is included in an exterior painting estimate?
A thorough estimate lists the walls, trim, soffits, fascia, doors, shutters and garage door that will be painted, the prep for each, the number of coats and the products. Gutters, railings, decks and window frames may be extra. Ask what is excluded, how stains or bare spots will be handled and who covers plants and furniture.
Can shutters and the front door be painted without removing them?
Yes, though removing shutters gives cleaner edges and backs, and they can be sprayed or brushed on sawhorses. Vinyl or plastic shutters take paint made for plastic or vinyl, in a color similar to or lighter than the original so they do not warp. Front doors can be painted in place with the hinges and hardware masked, then propped open until dry so they do not stick. Use an exterior primer and a durable satin or semi-gloss finish.
Can vinyl siding, stucco or fiber cement be painted?
Yes, with the right preparation and product. Vinyl is usually painted with a vinyl-safe paint in a similar or lighter shade than the original, because dark colors absorb heat and can warp it. Stucco needs cracks patched and a breathable masonry paint. Fiber cement takes paint well when it is clean and primed. Ask the painter which primer and paint match each surface on your house.
How many coats of paint does a house exterior need?
Most exteriors get a primer on bare, patched or stained areas and two coats of finish paint. Primer helps the paint stick and blocks stains, and the second coat gives color depth and film thickness. A coat that is too thick can crack, so pros let each coat dry fully. If you are changing from a dark to a light color, or painting bare wood, you may need extra coverage.
What sheen should I use on a house exterior?
Satin and low-sheen finishes are common for siding because they shed dirt and hide small flaws, while semi-gloss is often used on trim, doors and shutters for easier cleaning and a crisp contrast. Flat finishes hide imperfections but hold dirt more. Higher sheens show every dent and lap mark. Ask for a small sample board and check it in daylight before approving.
Why does my exterior paint chalk, stain with red dirt or grow mildew in Oklahoma?
Chalking is the powder that rubs off as paint ages in the sun, and it must be washed off before repainting. Oklahoma red clay splashes up from the soil during rain and stains lower siding and trim, so wash it off, spot-prime stubborn stains and keep soil, mulch and sprinklers away from the wall. Mildew grows in damp shade, and Tulsa's average relative humidity of about 66 percent helps it along. Ask for a mildew-resistant paint and fix gutters that overflow.
Can you paint over rotted wood?
No. Paint hides rot but does not stop it, and the coating will fail quickly over soft, damp wood. Rotted trim, fascia or siding should be cut out and repaired or replaced, then primed and painted, and the source of moisture such as a leaking gutter should be fixed. Small repairs are often done with the painting, while larger structural rot may need a carpenter.
Permits and rules
Do I need a permit or HOA approval to paint my house?
A city permit is usually not the issue. The City of Tulsa's Development Services page lists painting walls among the projects that do not require a permit. Permit requirements vary by city, so check where you live. The bigger question is an HOA or historic district, which can require approval of colors or of painting unpainted masonry. Read your covenants and call before work begins.
Choosing a contractor
Should I paint my house exterior myself?
Single-story ranch exteriors in good shape can be a weekend DIY project if you have the time. Two stories, steep roofs, scraping and repairs add ladder risk and take far longer. Add the cost of sprayers, scaffolding and extra coats, and know that homes built before 1978 fall under lead-safe rules for paid work. A good compromise is to hire out the high work and do the low trim yourself.
Next step: residential painting
Risks and safety
Is lead paint a concern when painting a house exterior?
It is if the house was built before 1978. Scraping or sanding exterior surfaces can spread lead dust into soil and around the home. EPA's Renovation, Repair and Painting rule requires paid painters to be certified, and in Oklahoma firms are certified by the state DEQ. Ask for proof before work, and keep children and pets away from the work zone.
Next step: residential painting
No question matches that search. Call (918) 704-5861 or request an estimate and ask us directly.
Still have a question?Call (918) 704-5861get an estimate.
Other painting that goes with this

Residential
Interior Painting
Careful prep, patching and clean lines on walls, ceilings, trim and doors.

Residential
Residential Painting
Choose exterior, interior or cabinets for your home.

Residential and commercial
Cabinet & Trim Painting
Update kitchen cabinets, vanities and built-ins without a full remodel.
Planning to paint your exterior?
Tell us about your house, the sides you want painted and your ZIP. We will call you back.


